Cracks in a Plaster House: What They Mean and When to Worry

Spotting a crack in your exterior plaster doesn’t automatically mean you have a major leak, nor does a tiny crack guarantee everything is fine. Because monolithic cladding cracks for many reasons, you can’t judge the health of your framing from the surface alone. Use the crack as a guide for where to investigate further, and as a prompt to bring in a qualified expert if it keeps coming back, gets bigger, or shows up alongside signs of moisture inside. This guide covers what monolithic cladding is, why cracks appear, which signs are worth a professional assessment, and what you can safely do in the meantime. What is monolithic cladding? In New Zealand, “monolithic cladding” describes wall cladding with a smooth, continuous finish made to look like plastered masonry. Instead of overlapping boards with visible joint lines, the wall reads as one surface, and it relies on its protective coatings to keep the weather out. That one look can cover quite different systems. Guidance published by the former Department of Building and Housing (now part of MBIE) gives three examples: Stucco: solid plaster applied over reinforcing and a backing. Flush-finished fibre-cement: sheets fixed to the building, with the joints stopped and a texture coating over the top. EIFS (exterior insulation and finish systems): a plaster finish applied over insulation board. Each is built differently, has different weak points and is repaired differently. From the street, they can look almost the same. The finish alone won’t tell you what’s underneath, whether there’s a drained cavity behind it, or how the windows and junctions were detailed. If you’re not sure what your home has, the original building consent documents, often held on the council property file, are a good place to start. You can also read about the systems we work with on our Exterior Plastering and Cladding page. Why do exterior plaster cracks appear? There’s rarely one answer, and a photo can’t give it. The usual possibilities are: Movement. Framing and other building materials move a little as they take up and lose moisture, and as a house flexes. A rigid plaster finish can crack where that movement concentrates. Heat and moisture cycles. Sun, rain and wind make surfaces expand and contract. MBIE’s diagnosis guidance lists dark paint colours among the factors to look out for on flush-finished fibre-cement and EIFS. Impact. A knock from a ladder, a mower or a car door can damage the coating or the backing behind it. Joints. Control joints are there to let a wall move in a planned place. Where they’re missing, in the wrong spot or have failed, the movement can show up as a crack somewhere else. Wear. Coatings and sealants deteriorate over time, faster without maintenance. In Wellington it’s natural to think of earthquakes first, but a crack isn’t automatically earthquake damage. Several of these causes look alike on the surface. That’s why the cause needs to be identified, not assumed. Hairline cracks and recurring cracks Seeing a crack and knowing its cause are two different things. A fine hairline crack may be limited to the surface coating. It may also be the visible edge of something else. Width alone doesn’t settle the question, so you won’t find a “safe” width in millimetres here. How the crack behaves over time tells you more: Does it come back after it has been filled or painted? Is it getting longer or wider? Have new cracks appeared nearby? Does it line up with a window corner, a floor level or a joint? A crack that keeps coming back or keeps changing is a reason to look for the cause rather than cover it again. Cracks around windows, joints and penetrations Where a crack sits matters as much as how it looks. Window and door openings, joints in the cladding, corners, the line between storeys, and any spot where pipes, cables or fixings pass through the wall all depend on careful detailing and sealing to keep water out. MBIE’s diagnosis guidance names several of these as common problem areas for monolithic claddings, including failed or poorly maintained coatings and joints, and junctions that rely on paint, texture coating or sealant to seal around windows. It also points to the ends of apron flashings (where a lower roof meets a wall) and the clearance between the bottom of the cladding and the ground. You can check most of this from the ground. Walk around the house on a dry day, use binoculars or your phone’s zoom for the upper storey, and look at the same walls from inside. Please don’t climb ladders, get on the roof or put up scaffolding for a closer look. Leave that to someone with the right equipment and training. Which signs need professional assessment? Arrange a qualified assessment if a crack is recurring or changing, especially if you also notice any of these: staining or discolouration on walls, ceilings or skirtings near the cracked area a musty or damp smell in a room paint bubbling, flaking or lifting on the plaster swollen skirtings or trims, or mould on interior surfaces the coating or the material under it breaking down around the crack water dripping from the soffits or the bottom of the cladding long after rain has stopped These all appear in MBIE’s list of possible signs of moisture problems. Two cautions go with that list. First, a sign doesn’t prove a cause. Damp inside can also come from a plumbing leak or a steamy bathroom, as the same guidance points out. If you suspect water is getting in, or that there’s a structural problem, get the right kind of professional to look. Depending on what’s found, that could be a cladding specialist, a building surveyor or weathertightness assessor, or a structural engineer. What should you do before a crack repair? Start a simple record. It costs nothing and makes any assessment more useful. Take a wide photo that shows where the crack sits on the wall, then a close-up. In

Cracks in a Plaster House: What They Mean and When to Worry Read More »